MMCX Micro-miniature connectors with characteristic impedance of 50 ohm has been designed to achieve a high level of electrical performance and provide repeatable electronic performance from DC to 6 GHz. The “snap-on” mating design offers low RF leakage and ease of assembly in dense packaging arrangements. Typical applications include wireless/PCS devices, telecommunications, GPS receivers, wireless LAN (WLAN) applications and consumer electronics. ...

The reverse polarity design prevents damage and cannot be mated with standard interface devices if accidentally connected.  Reverse polarity non-standard interface connectors are designed for spread spectrum wireless applications where part 15.20 of US FCC regulations are applicable. Reverse polarity are available in SMA, BNC, N, and TNC versions of male and female crimp. Featuring all crimp terminations, these connectors feature performance consistent with the corresponding non-polar...

The Type N connector was developed to satisfy the needs for a durable, weatherproof, medium-size RF connector with consistent performance through 11 GHz. The N connector is the most practical and popular coaxial cable connector for 7mm *inner diameter of outer conductor) of 50W group. The coaxial connector can be supplied with characteristic impedances 50 ohm and 75 ohm. The thread coupling incurs low noise and withstands shock and vibration. Applications include power transmitters, commun...

Cable assemblies from DC to 18 GHz in a wide range of RF connectors. As with our connectors, the cable used within an assembly is selected to perform precisely to your requirements. We can meet your needs using cable such as RG58/59, URM types right through to high temperature cables such as RG178/179/188/316.We also supply a variety of custom cable assemblies to meet your exacting requirements. We can provide MCX, MMCX, SMA, SMB, SMC, BNC, TNC, N type, UHF, Mini UHF, and FME series cable ...

MCX micro-miniature connectors with characteristic impedance of 50 ohm have been designed to achieve a high level of electrical performance and provide repeatable electronic performance from DC to 6 GHz. They have a “snap-on” system. MCX connectors are approximately 30% smaller than SMB type connectors but use the same proven internal interconnect arrangement with regard to the dielectric and center contact. Typical applications include PCMCIA cards small – held communica...

The SMC is similar in design to the SMB, except it has threaded coupling interface, instead of a snap-on interface. These screw on designs operate reliably to 10 GHz at a 50 ohm impedance. SMC types have a 10-32 UNF threaded coupling. This is a good choice for applications where the need for small size and performance in high vibration environments are a concern, To reduce the difficulties of assembly inherent in this type of connector, the polarized centre contacts are tape mounted for ea...

SMB connectors are semi-precision, subminiature series devices that provide repeatable electrical performance from DC to 4 GHz. available in 50ohm and 75 ohm impedance. These subminiature connectors are best suited for use with cables in the range of .070” to .120” diameter, such as RG174, RG178, and RG316/u. Its smaller physical size and “ snap-on” coupling design make the SMB an ideal fro general purpose connector where packaging density, ease of mating/un-mating ...

SMA connectors are cost-effective, semi-precision, subminiature units that provide excellent repeatable electrical performance from DC to 12.4 GHz with flexible cable. They are best suited for use with fight-frequency semi-rigid cables that extend the frequency range of the device to 18 GHz. This series of SMA connectors with characteristic impedance of 50 ohm has been designed to achieve a high level of electrical performance. These properties, minimum attenuation and low VSWR have made t...

SSMA subminiature connectors for semi-rigid cable meet performance requirements for microwave and other applications where reduced size and higher packaging density is important. The standard SSMA series allows operation up to 38 GHz. The coupling thread is 10-36 UNS thread. SSMA connectors are also available as panel mount, bulkhead mount, strip transmission line type, micro-strip transmission type, printed circuit board mounting, and as hermetically sealed connectors. ...

BNC connectors are miniature, lightweight units designed to operate up to 4 GHz and typically yield low reflection through 4 GHz. The special bayonet design provides easy mating/un-mating. BNC series is most widely used as 50W coaxial cable connectors. Various connectors available in 50 and 75 ohm versions. BNC connectors are designed to accommodate a large variety of RG and industry standard cables. BNC series are used in a wide range of applications such as flexible networks, instrumenta...